Dark circular logo badge with stylized gold lettering on a deep brown background, warm and equestrian in tone. Schramm Equestrian

Eventing Tack Maintenance And Cleaning Routine

Reliable tack is part of reliable performance in eventing. A bridle that stays supple, a girth free from dried sweat and a saddle checked for hidden wear can make schooling more comfortable for both horse and rider. Regular care also helps equipment last through flatwork, show jumping and the demanding conditions of cross-country.

For riders in Australia, a practical routine needs to account for red dust, hard water, intense sun, summer humidity and long journeys between competitions. Whether the kit is used at home near West Grove, Pennsylvania, or at venues such as Scone, Werribee or Adelaide International, the basic principle remains the same: clean often, condition thoughtfully and inspect before small faults become expensive problems.

Begin With A Quick Tack Inspection

Before removing dirt, look over every piece of equipment. Run your fingers along stitching, billets, keeper loops, buckle attachments and areas that sit beneath the horse’s jaw or behind the ears. Cracked leather, stretched holes and loose stitching deserve attention before the next ride, particularly when tack will be used over solid fences.

Check the saddle panels, girth straps and stirrup leathers for uneven wear. On a three-day event horse, equipment may be used for several phases in quick succession, so a small weakness can become serious under pressure. Keep a separate note of repairs needed and take items to a qualified saddler or reputable local tack shop rather than relying on household glue or improvised stitching.

A short inspection after every ride is easier than a major restoration session. If the horse has sweated heavily, wipe the tack before the salt dries into the leather. This is especially useful during a Queensland summer or a warm competition weekend in New South Wales, when sweat can stiffen and damage frequently used areas.

Remove Dust Before Applying Products

Start with a soft, dry brush or clean cloth to remove sand, arena dust and loose hair. Pay attention to stitching channels, buckle holes and the underside of the noseband. Rubbing wet mud into leather can push grit deeper into the grain, creating abrasion where the bridle bends or the girth moves.

Use a slightly damp sponge for ordinary grime, followed by a dry towel. Avoid soaking bridles, reins or saddle flaps, since excess water can swell the leather and weaken its shape. If tack is covered in wet clay after a cross-country round, allow the worst of it to dry enough to brush away, then clean the remaining residue gently.

Australian riders often deal with fine dust that travels everywhere, from a dry Victorian arena to a western Sydney float yard. A dedicated tack-cleaning kit kept in the truck can include a soft brush, several microfibre cloths, a small bucket, leather cleaner and a hoof pick for clearing compacted mud from buckles.

Clean Leather In Small Sections

Apply a pH-balanced leather cleaner sparingly with a damp sponge. Work in small sections, using light circular motions without flooding the surface. Open buckles and clean underneath them, then wipe away residue before moving on. Leaving cleaner in folds or around metal fittings can attract grime and encourage deterioration.

Saddle soap may be useful for routine cleaning, but it should not be treated as a substitute for every other product. Some modern coated leathers need a manufacturer-approved cleaner, while heavily conditioned leather can become soft and lose its structure. Test any unfamiliar product on an inconspicuous area first, especially when caring for an expensive eventing saddle.

After cleaning, let the leather dry naturally in a cool, ventilated place. Do not put it beside a heater or leave it in the boot of a car during an Australian summer. Rapid heat can cause leather to shrink, harden or crack, and a closed float compartment can trap humidity after a sweaty training session.

Condition For Flexibility And Grip

Once the leather is clean and almost dry, apply conditioner lightly to areas that flex frequently. Reins, cheek pieces, girth billets and stirrup leathers generally need more attention than firm saddle panels. Use a clean cloth and build up thin layers rather than applying one heavy coating.

Too much oil can soften structural leather and leave a slippery surface. That matters when a rider needs a secure rein contact or when a saddle must remain stable over undulating cross-country ground. Keep conditioner away from suede or other specialist materials unless the manufacturer specifically allows it.

Dom and Jimmie Schramm’s riding careers show how eventing depends on coordination between horse, rider and equipment; readers can learn more through Dom's eventing profile. A consistent leather-care routine supports that partnership by keeping the tack comfortable, predictable and ready for work.

Wash Bits, Girths And Synthetic Gear

Metal bits should be rinsed after every use and dried before storage. A soft toothbrush can remove saliva and feed residue around the rings and joints. Inspect the mouthpiece for sharp edges, damage or unusual wear, and replace a bit if its surface is rough or compromised.

Girths collect sweat, hair and arena dust, so they need more than an occasional wipe. Follow the care instructions for leather, neoprene, mohair or synthetic materials. Many fabric girths can be rinsed or washed gently, while leather girths need controlled cleaning and careful drying. Never store a damp girth in a closed tack locker.

Synthetic bridles and saddle accessories can be convenient for wet conditions or frequent travel, but they still require cleaning. Rinse salt and dust away, dry them fully and check hook-and-loop closures, elastic sections and plastic fittings. At a busy Australian event, where gear may be packed in and out between phases, labelled kit bags help keep clean and dirty equipment separate.

Store Tack To Prevent Damage

Store bridles on a proper hanger and keep reins untwisted. Saddles should rest on a shaped rack with enough support through the panels, rather than being balanced on a narrow rail. Cover them with breathable covers that keep off dust without trapping condensation.

Avoid leaving leather in direct sunlight, damp sheds or an unventilated float. In coastal areas such as the Sunshine Coast, salt-laden air can affect metal fittings, while dry inland conditions can pull moisture from leather. A stable tack room should be clean, shaded and reasonably consistent in temperature.

Before travelling to a competition, check girth billets, stirrup bars, breastplates, martingales and safety equipment. Riders who travel from Melbourne to Werribee or make long runs towards Scone should allow time for a final inspection rather than cleaning in a rush beside the warm-up arena. Keep a basic repair kit, spare stirrup leathers and replacement keepers with the competition gear.

Build A Routine Around The Training Week

After every ride, wipe down the bridle, bit, girth and any visibly sweaty leather. Once a week, carry out a more complete clean and inspect stitching, buckles and saddle contact areas. After a competition, give every item a deeper clean before it returns to storage, even if the tack looks acceptable from a distance.

A monthly review is a useful time to assess fit, wear and upcoming repairs. Saddles should be checked by a qualified professional at suitable intervals, since horse shape and workload can change. Riders who also focus on conditioning can use a dedicated rider conditioning guide to support balance, strength and stability away from the saddle.

Cleaning should never disguise a fit problem. White hairs, rubs, uneven sweat marks or a horse resisting tacking up may indicate that the saddle, girth or bridle needs professional assessment. Likewise, a training plan involving related distances and jumping exercises should include equipment checks; this related-distance guide provides useful context for the precision required in show jumping.

Make tack care part of the final few minutes of every ride. Brush away dust, rinse the bit, hang the equipment properly and record anything that needs repair. That small habit keeps eventing gear competition-ready and gives horse and rider the best chance to perform with comfort, confidence and consistency.